Introduction Accurate characterization of frequency-dependent inhomogeneous dielectric material properties is key to the optimal design of high performance and cost-effective PCB antennas. These antennas will be required to enable the plethora of devices forecasted for 5G/6G communication. Therefore IT-88GMW, an advanced resin system reinforced with tightly woven thin glass fibers has been formulated to improve the Q-factor of interconnects and passive components fabricated on PCB laminates. 

Introduction Accurate characterization of frequency-dependent inhomogeneous dielectric material properties is key to the optimal design of high performance and cost-effective PCB antennas. These antennas will be required to enable the plethora of devices forecasted for 5G/6G communication. Therefore IT-88GMW, an advanced resin system reinforced with tightly woven thin glass fibers has been formulated to improve the Q-factor of interconnects and passive components fabricated on PCB laminates. 

The electrical and thermomechanical properties of dielectric materials primarily determine the performance of high-speed circuitry fabricated on PCB laminate technology. Therefore, a recommended practice for PCB fabrication is to implement characterization methodologies that provide relevant information about the material's performance in realistic scenarios. Hence, rather than limit characterization to solely obtaining nominal data at particular frequencies by assuming signal propagation in a direction of best performance, the material characteristics should be analyzed in different directions and positions. This gives the designer a clearer idea of how much variation to expect in an actual implementation, in contrast to ideal conditions that are typically assumed to simplify the design cycle. 

In selecting a laminate material for a high-speed/frequency antenna design, the composite material properties are critical parameters that will determine if the antenna patches and network of interconnects to be fabricated can meet the loss, timing delay, and impedance match requirements of the application. PCB laminates are typically manufactured in two ways: 

In addition to optimal electrical properties, dielectric materials for high speed/frequency applications are engineered to exhibit improved thermal reliability, dimensional stability, and low moisture absorption. The resin matrix at the core of these systems has greatly evolved from standard epoxy to olefin chemistries which exhibit the desired electrical properties of PTFE-like substrates, but also offer ease of processing and low reliability risk. 

To read this entire article, which appeared in the March 2022 issue of PCB007 Magazine, click here.

Introduction Accurate characterization of frequency-dependent inhomogeneous dielectric material properties is key to the optimal design of high performance and cost-effective PCB antennas. These antennas will be required to enable the plethora of devices forecasted for 5G/6G communication. Therefore IT-88GMW, an advanced resin system reinforced with tightly woven thin glass fibers has been formulated to improve the Q-factor of interconnects and passive components fabricated on PCB laminates. 

The electrical and thermomechanical properties of dielectric materials primarily determine the performance of high-speed circuitry fabricated on PCB laminate technology. Therefore, a recommended practice for PCB fabrication is to implement characterization methodologies that provide relevant information about the material's performance in realistic scenarios. Hence, rather than limit characterization to solely obtaining nominal data at particular frequencies by assuming signal propagation in a direction of best performance, the material characteristics should be analyzed in different directions and positions. This gives the designer a clearer idea of how much variation to expect in an actual implementation, in contrast to ideal conditions that are typically assumed to simplify the design cycle. 

In selecting a laminate material for a high-speed/frequency antenna design, the composite material properties are critical parameters that will determine if the antenna patches and network of interconnects to be fabricated can meet the loss, timing delay, and impedance match requirements of the application. PCB laminates are typically manufactured in two ways: 

In addition to optimal electrical properties, dielectric materials for high speed/frequency applications are engineered to exhibit improved thermal reliability, dimensional stability, and low moisture absorption. The resin matrix at the core of these systems has greatly evolved from standard epoxy to olefin chemistries which exhibit the desired electrical properties of PTFE-like substrates, but also offer ease of processing and low reliability risk. 

To read this entire article, which appeared in the March 2022 issue of PCB007 Magazine, click here.

White Paper: With the move from low-mix to high mix-manufacturing, the need for optimizing throughput across multiple batches of different product is critical to maximizing manufacturing output. Overall line utilization... View White Paper